How To Develop Film With The “Stand” Technique


The World of analog photography keeps surprising me every day a bit more! I recently read about a technique called Stand Development so I have decided to try it myself. For those of who never heard of it before, let me explain you the differences between a normal development process.

When developing, as recommended by manufacturers, we are supposed to make regular agitations to ensure that the exposed film is always in contact with fresh developer. This is because the developer exhausts itself after a while and is no longer able to transform the particles of silver on the emulsion. Agitations also ensure that all the tonalities are evenly revealed.

/Vincent Moschetti

On the contrary, stand development consists in letting the developer sit inside the tank with only one minute of agitation at the very beginning. Without movement, the areas that require more development quickly exhaust all the developing agent whilst it keeps acting on the less exposed areas that don’t weaken the developer so much. This has for effect to preserve highlights and reveals more details in the shadows.

On top of that, I see two other advantages that are directly linked with this lack of movement in the developing tank:

1. High Contrast

This is a question of tastes but I tend to prefer my pictures to be more contrasty, especially for black and white. I believe that it gives more character and help to drag attention on the subject. This is, of course, a personal opinion and it may not work with all styles of photography. The pictures that you are going to see next, barely received any adjustments and came out naturally contrasty. Fomapan is not known for having contrasty films, it’s more the opposite, they tend to be more of a flat look.

/Vincent Moschetti

2. Fine details:

Because the developer is not moving, the acutance is very high. If acutance is a new word for you too, check out the definition here on Wikipedia. It makes edges very sharp between dark and bright areas, hence the increased sharpness. I was already very satisfied with the quality of the glass on my Hasselblad Xpan but, as you will see below, the amount of details that came out from my last roll is insane…I feel like I have a new lens!

Another advantage is that it’s a low dilution process. With normal development, the dilutions are usually between 1+1 and 1+4. Here we are using a very low dilution so you can save a lot of developer. Depending on the developer, you can dilute up to 1+50. This means that for 1 litre of pure developer, you can do 50 litres of developing solution!! Considering that one roll of 35mm needs more or less 300ml of solution, you could develop up to 150 rolls… Knowing that one litre of developer cost in average $18 so it would less than $0.12 of chemical to develop per roll!

/Vincent Moschetti

Before we end with the math lesson, let me give you more information about the dilution I used.

The most common developer for this technique is usually Rodinal which is diluted at 1+50. Here I only had Ilfotec DD-X and found that it should be mixed at 1+9. As I was using a Patterson tank with only 1 roll of film, I needed 300ml of solution. So I mixed 30ml of developer with 270ml of water at 20 degrees Celcius. Then I agitated for the first minute, tapped the tank on the 3 or 4 times to remove air bubbles from film and let it sit for 45 minutes. After that, one minute of stop bath and three minutes of fixer. And that’s all folks !!

3. Patient Results

As soon as I saw the negatives, I knew that these images would turn good (for my taste at least). I have developed a few rolls already but never saw a negative so dense and contrasty. Sometimes it’s hard to differentiate the shapes but here everything was clearly distinct and sharp. The comparison with a normal negative of Fomapan 400 is unbelievable, it looks like I shot a completely different film.

/Vincent Moschetti

The only downside I have found so far it is the time it takes. Some stand development can take one hour and more so you have to be patient. But it’s the perfect opportunity to scan some negatives for example. You can also read that some people experienced uneven development or the apparition of streaks due to a chemical reaction that falls at the bottom of the tank. This can be avoided by making one or two inversions mid-development, in this case we talk about semi-stand development. Personally, I didn’t notice anything strange, but it might have something to do with the low dilution I used, comparing to what it should be with Rodinal for instance.

Another important point to mention: With this process, you can mix in the same tank two films that are rated at different speeds. This also lets me think that it doesn’t matter too much if you pushed your film, but I am not sure about this and will have to make some tests to determine if you need to extend the time when pushing film. I feel like I have just opened another door that will lead me towards more adventures into the film photography experience! It’s like I am playing with Russian Dolls.

/Vincent Moschetti

Vincent Moschetti worked exclusively with digital equipement until he had a revelation and discovered the beauty of shooting with film cameras.If you would like to learn more about his work, you can visit his websiteFacebook, and Instagram pages. This article was originally published here.

(Cover image: Vincent Moschetti) Images Used With Permission